LUBRICANT SPECIAL FOR METAL CABLES, HANDLING AND LIFTING CHAINS,
OPEN GEARS
EXTREME PRESSURE, ANTI-WEAR
COMPLETELY WATER RESISTANT – SUBMERGED LUBRICATION
DESCRIPTION
Highly adhesive complex fluid, penetrant, for the lubrication of power transmissions subject to vibration phenomena.
Protects against corrosion.
Is not affected by dusty environments or water spray; can be used in a marine environment.
Highly loaded with solid lubricants, anti-ware and anti-corrosion additives, provides optimum lubrication in extreme cases.
APPLICATIONS
- Port and public works equipment, chains, cables, steering crown wheels, capstans, headstocks.
- Dams, lakes, airlocks, water locks, lubrication of lifting chains, hoists, machinery.
- Hydroelectric production.
- Cement mills, mineral extraction, conveyors.
- Smelting, transporters.
- Handling equipment, bridge cranes, gear trains, fifth wheel couplings.
- Pre-impregnation and weaving of cables.
- Mounting and lubrication of roller, riveted or API chains.
- Fairground equipment.
INSTRUCTIONS FOR USE
Vigorously shake the aerosol vertically.
Spray surfaces to be treated from a distance of 15 to 20 cm.
For polyamide, polyester or polypropylene textile slings, use NEOLUBE® T20.
AEROSOL Neolube® OPEN GEAR IS GUARANTEED METHYLENE CHLORIDE FREE
TYPICAL PHYSICAL-CHEMICAL PROPERTIES
|
PHYSICAL PROPERTIES OF THE LUBRICATING OIL |
|||||
|
PROPERTIE |
STANDARD or METHOD |
VALUE |
UNITS |
||
|
Appearance |
visual |
Viscous fluid |
nm |
||
|
Colour |
Visual |
Dark brown |
nm |
||
|
Scent |
Olfactory |
Slight |
nm |
||
|
Density at 20°C |
NF EN ISO 12.185 |
850 |
g/l |
||
|
Nature of solid lubricants |
- |
Graphite |
- |
||
|
Nature of base oil |
- |
Hydrocarbon/Polymer |
- |
||
|
Kinematic Viscosity Base oil at 40°C Base oil at 100°C |
NF EN ISO 3,104 |
180 98 |
mm2/s-1 mm2/s-1 |
||
|
Sulphated ash |
NF T 60.144 |
< 1.5 |
% |
||
|
Acid index (ai) |
EN 14,104 |
< 1 |
mg(KOH)/g |
||
|
Closed-cup flash point |
NF EN 22.719 |
150 |
°C |
||
|
Self-combustion point |
ASTM E 659 |
>200 |
°C |
||
|
Freezing point |
ISO 3016 |
-25 |
°C |
||
|
Impurities > 25 µ > 75 µ > 125 µ |
FTMS 791 3005 |
0 0 0 |
number/ml number/ml number/ml |
||
|
PERFORMANCE PROPERTIES |
|||||
|
PROPERTIE |
STANDARD or METHOD |
VALUE |
UNITS |
||
|
Utilisation temperature range |
- |
-20 +80 |
°C |
||
|
Copper blade corrosion 24h 100°C |
ISO 2160 |
1b |
value |
||
|
Loss by evaporation 22h at 121°C |
ASTM D 972 |
13.8 |
% mass |
||
|
SHELL 4-ball test Impression diameter Weld load index |
ISO 20.623 – ASTM D 2266 |
0.62 3800 |
mm N |
||
|
SRV test |
ASTM D 5707 |
0.18 |
coefficient |
||
|
Elastomer swelling test (dimensional change) |
FTM 791 |
1.5 |
% |
||
|
Suppression of operating noise |
FAG MMG 11 |
1 |
category |
||
|
Maximum permitted speed |
- |
0.001 |
m/s-1 |
||
|
Water wash-off resistance at 80°C |
ASTM 1264 |
<-1 |
% |
||
|
Cold starting torque at -20°C |
ASTM D 1478-63 |
25 |
N.cm |
||
* nm: not measured or cannot be measured
PRESENTATION
"Guaranteed without HFC greenhouse effect"
|
Aerosol 650 ml |
Looking for another product?
|
Discover our entire range by clicking on the photo |
.jpg)
Manufacturing, lubrification, cleansing, protection,
IBiotec® Tec Industries® Service
offers a wide range of products reserved for industrial area
If you wish for :
a free sample
a technical advice
a product data sheet
a safety data sheet
IBiotec® Tec Industries®Service
manufacturer of technical chemical products.
Welcome to our website.
IBiotec® Tec Industries®Service is on : 